Lathe

 

Like New Condition

I acquired this lathe in 2014 and used it that one show season only on the Woodworking Show Circuit for show demonstrations. It has been in climate controlled storage since. The condition is like new and I would call it very lightly used. This is the 1-1/2 HP 110v version so it should work in any shop with no need for 220v.

I have acquired a new Jet 1840EVS and do not need this lathe. Retail value new is $2499.99 so your savings are significant. You can see it run and examine it in person if you wish. It worked fine the last time I used it. You may inspect it on site. No warranty is expressed or implied except my personal reputation for treating folks fairly.

$2,000 Cash Only- Firm. Ron Brown (770) 962-3821 Eastern.

Local pick up only (northeast Atlanta, Ga suburb) This lathe disassembles and reassembles in about 10 minutes with two people. The heaviest piece is the headstock-motor assembly at around 130 pounds. The cast iron legs unbolt and are easily carried by one person. You can easily haul it in an SUV, pickup or van. If you need to travel to pick it up, I may hold the machine for you a couple of days with a deposit. Otherwise, first come, first served.

Note:

The tool basket shown is not included. There may be some very slight cosmetic scratches consistent with a lightly used machine.

  • 1-1/2-horsepower electronic woodworking lathe
  • 16-inch swing, 42-inches between centers; variable speed (0-3,200 rpm)
  • Cast-iron bed and legs
  • Includes lathe, tool rest, faceplate, spur center, live center, knockout bar, tool storage rack
  • 410-pounds for reduced vibration; 63-1/2 by 20 by 50-inches; 

Offering a one-inch swing over the bench and 42-inch capacity between centers, the JET 708359 JWL-1642EVS Woodworking Lathe, 115-Volt 1 Phase is ideal for home shop use. Boasting the versatility of a sliding headstock, electronic variable speed, and the necessary capacity for large projects, the JET JWL-1642EVS is a great lathe for beginning and serious craftspeople alike.

Three-Phase Motor with Electronic Inverter for Powerful Performance
The JWL-1642EVS comes equipped with a 1-1/2HP, three phase, 115-volt motor for shops that do not have 220-volt power available. An electronic inverter does all the work to convert from the "1 phase" to "3 phase." The inverter also provides the ability to vary the frequency of the motor, which in turn allows for variable speed.

Cast-Iron Castings for Stability and Smooth Operation
Based on heavy-duty iron castings, the JWL-1642EVS provides long-term accuracy and smooth, vibration-free operation. Even the legs are made from an iron casting and include cast-in supports and adjustable pads at each foot to ensure a solid stance on uneven surfaces. With these legs, the spindle (center) height is a comfortable 44.5 inches above the floor.

The JWL-1642EVS headstock is also made from a massive iron casting that provides rigid support for the 1-1/2 HP, variable speed motor(0 to 3,200 RPM), and the high-strength spindle. After machining, the headstock is fitted with large diameter, high-quality ball bearings that support the precision-machined spindle for reliable performance.

Large-Diameter Spindle with Built-in Indexing for Drilling, Fluting, and More
The large-diameter spindle has a 1.25 x 8 threads-per-inch nose that supports the large chucks typically used with this type of lathe. Additionally, the outboard end of the spindle is fitted with a barrel-type grip for turning the spindle by hand. The spindle also has internal indexing built in that allows you to lock it in 36 positions (or 10-degree increments) for drilling, fluting, grooving, and other operations.

For added convenience, the spindle is indexed with a screw-in pin provided with the lathe. There's also a push-button spindle lock on the front of the headstock for a simple, tool-free way to temporarily lock the spindle when you install or remove the faceplate, chuck, or other screw-on accessories.

Heavy-Gauge Wire Guard for Safety
A special mount on the rear of the headstock accepts a heavy-gauge wire guard (included), and a spring-loaded pin indexes the guard up or down to make mounting and removing turned objects easy. This guard also serves as a protective shield between the work and the operator, when large chips and chunks generated while turning blanks can turn into dangerous projectiles.

User-Friendly Controls, LED, and Toggle Switch
Designed to be user-friendly, the JWL-1642EVS features dial-operated, infinite speed controls conveniently located on the front of the headstock. A large digital LED readout makes monitoring the spindle speed easy and very accurate, while the toggle switch on the front panel allows selecting forward and reverse spindle directions. Finally, a large-diameter pull on/push off button (also on the front panel) is easily accessible no matter your operating position.

Large Tailstock for Stability
The JWL-1642EVS has a large tailstock with the mass and wide base to generate the stability you need. The large ram has a full four-inch travel, operated by an easy-to-turn, five-inch diameter handwheel fitted with a spinner handle, the popular #2 Morse taper, and a 3/8-inch diameter through hole, which is convenient for drilling lamp bases. Finally, like the tool-rest base, a large handle makes it easy to lock the tailstock securely in place.

Ball bearing Live Center and Cast Iron Tool Rest Base for Versatility
The JWL-1642EVS comes with a high-end, multi-row ball bearing live center with a screw-on, large-diameter cone for projects like peppermills and boxes, and a cast-iron tool-rest base designed to be very rigid, easy to position, and thanks to its comfortably long handle, very easy to lock in position.

The JWL-1642EVS measures 29 x 28 x 59 inches (WxHxL), weighs 410 pounds, and is covered by a five-year warranty.

About JET: A History of Sharing New, Feature-Rich Products
Opened in 1958 after the founder of the company, Leslie P. Sussman, took the first Boeing Jet Airplane trip from Seattle, Washington to Japan, JET began as a small dealer that sold air hoists and trolleys out of a single hardware store in Seattle. Over the years, JET has carried everything from snowmobiles, transmitter radios, and forklifts to nylon stockings, but by the early 1970s, metalworking had become the base of their business line. And by the 1980s, JET had expanded into the realm of woodworking. Today, you'll find that JET offers a wide range of popular woodworking tools that are backed with best-in-class features and excellent service.

 


There are no products to list in this category.

Featured

Turners Laser Guide 7386

Turners Laser Guide 7386

The Turners Laser Guide enables you to know the location of a point on the cutting edge in real ti..

$79.99

10 inch Longworth Style Chuck 7365

10 inch Longworth Style Chuck 7365

Longworth Style Lathe Chuck Longworth Style Lathe Chucks are the perfect solution for finishing..

$139.99

Universal Setting Jig Lathe tool Sharpening

Universal Setting Jig Lathe tool Sharpening

Universal Setting Jig Lathe Tool Sharpening  New!  Wouldn’t it be wonderful if, you could pick up a..

$29.99

Latest

Should You Turn Pro

Should You Turn Pro

Should You Turn Pro ..

$0.00

CBN Grinding Wheel 80 Grit 9856

CBN Grinding Wheel 80 Grit 9856

Manufacturers recommend wheels made of CBN—not diamond—for sharpening tool steel. CBN is cubic boron..

$189.99